Miracle Sealants 511 Impregnator, Quart

Miracle Sealants
SKU:
30.10110
$32.20
(3 reviews)
Current Stock:
Adding to cart… The item has been added

Miracle Sealants 511 Impregnator Sealer

511 Miracle Sealants Impregnator is the original penetrating sealer designed for the protection of all medium to dense porous surfaces. The sealer forms an invisible barrier that is resistant to moisture and stains while allowing vapor to escape. Miracle Sealants 511 Impregnator Sealer is not a surface coating and will not alter the natural look. All surfaces treated are harder and less slippery.

Confused by Sealers? Take a look here: Sealer Buying Guide


Uses:

  • Sanded Grout
  • Porcelain Tile
  • Concrete
  • Quarry Tile
  • Quartz
  • Polished Granite
  • Brick
  • Travertine
  • Ceramic Tile
  • Polished Marble
  • Stucco
  • Agglomerate
  • Glazed Tile
  • Terrazzo
  • Slate
Features:
  • Interior & Exterior Use
  • Weather Resistant
  • Less Expensive
  • OK for Food Areas
  • Superior Coverage
  • Easy to Use
  • UV Transparent
Application:
 

Before Grouting: Apply Miracle Sealants 511 Impregnator Sealer to all surfaces prior to grouting. This step will allow quick and easy cleanup after grouting. Grout can stain many surfaces if this procedure is not used prior to the grouting process. Apply using a Mira Brush or a clean towel. Apply enough to wet the surface. (See coverage charts) Be careful not to saturate the open grout joints. Allow to stand for approximately 3 - 5 minutes for maximum penetration. All excess must be removed at this time by buffing surface with a clean dry towel. This is very important on polished, glazed and porcelain surfaces. Allow Miracle Sealants 511 Impregnator Seal to cure for 12 - 24 hours before continuing with the grouting procedure.

 

After Grouting: Once grouted, make sure that all grout residue is removed from the surface with a clean sponge and water. Allow grout to cure per manufacturers specification. If grout clean up is not performed effectively, an additional cleaning may be necessary to remove remaining grout residue or haze. For this procedure use Phosphoric Acid Cleaner , (GCFR) Grout & Concrete Film Remover (Hydrochloric Acid), Sulfamic Acid Crystals or Epoxy Grout Film Remover following the instructions carefully. Once the area has completely dried, proceed with the sealing of the grout for water and stain resistance. Apply Miracle Sealants 511 Impregnator Sealer to all grout with a paint brush.

Any excess sealer that gets on the surface should be wiped off with a clean towel before it dries. On larger jobs grout can be sealed by retreating the entire area including the tile or stone surface a second time. Be careful not to allow the sealer to puddle or dry on presealed surfaces.

It covers approximately 1,000 - 4,000 square feet per gallon (90 - 364 square meters per 3.785 liters).

Product / Technical Data Sheet
30.10110:
511QT6

Reviews

  • 5
    Service

    Posted by Marvia Lackey

    Great prices and fast shipping

  • 5
    Miracle Impregnator Sealant

    Posted by Wendy Noe

    This was sooo easy to use. I recently had porcelain tiles installed on my front porch and stairs. I know most contractors say that it isn't necessary to seal porcelain tiles, but the grout needed to be sealed and the easiest way I found to do that was to seal the tiles and grout at the same time. After applying 2 coats of the sealer on the porch and stairs and letting it dry I've been noticing that, just as the product info states, the water that drips onto the treated areas beads up. The real test will be during a rainstorm. I'm hoping it lasts 25 years, as stated.

  • 4
    great service

    Posted by Tim Myles

    Great customer service. Easy to work with.