Home > Stone Care Products > Stain Removers > Aqua Mix >

Aqua Mix Poultice Stain Remover
Aqua Mix Poultice Stain Remover


 
Price: $7.15


Product Code: 30-38450


Size*:


Qty:  
Description
 

Aqua Mix Poultice Stain Remover

Aqua Mix Poultice Stain Remover is a dual purpose, non-acidic problem solver. It is an absorptive clay that is designed to remove deep-set oil and grease stains without scrubbing. It is also a fine abrasive cleaning powder that removes stubborn surface stains and light grout haze.

NOTE: Aqua Mix Poultice Stain Remover is an excellent additive that will boost the cleaning power of many of the Aqua Mix cleaners such as Phosphoric Acid Substitute, Heavy Duty Tile & Grout Cleaner, and Stone Deep Clean.


Uses

You can use Aqua Mix Poultice Stain Remover on all honed, unpolished natural stone (such as granite, limestone, marble, slate, and travertine), porcelain, quarry, Saltillo, terra-cotta, cement pavers, masonry surfaces, and other porous tile and grout


Features

  • Effectively removes deep-set oil and grease stains
  • Safe, non-acidic, abrasive cleaning powder
  • Excellent cleaning additive

Coverage

Approximately 25 to 750 sq. ft. per 3/4 pound, depending on dilution.


For Removing Deep-Set Oil And Grease Stains:

1) Read entire label before using.

2) Mix Aqua Mix Poultice Stain Remover powder with water to form a thick, pliable paste – quantity of Poultice Stain Remover needed will depend on size of stain.

3) Apply a 1/4-inch (6 mm) thick layer of paste directly over stain with at least a 1-inch (25 mm) overlap beyond edge of stain.

4) Cover with plastic or wax paper. Poke a few very small holes in plastic cover to allow for minimum air exposure.

5) Allow paste to stand on stain for 24 to 48 hours.

6) Remove Aqua Mix Poultice Stain Remover with plastic spatula or plastic putty knife and wash off residue with clean water.

7) Repeat procedure if necessary. If area darkens from absorbed moisture, it should dry completely within 2 to 4 days.



For Removing Stubborn Surface Stains And Grout Residue On Acid Sensitive Stone:

1) Read entire label before using.

2) Protect surrounding areas from splattering to minimize cleanup.

3) Pre-wet a manageable area of the surface with water (approximately 10 sq. ft. (1 m2) and sprinkle Poultice Stain Remover onto the area mixing into a thin slurry. If surface is vertical, mix slurry in a container and apply to pre-wet surface.

4) Agitate by hand or with low RPM (300-750 RPM) buffer using a white nylon scrub pad. Keep surface wet throughout buffing process.

5) Remove Aqua Mix Poultice Stain Remover solution with clean towels or sponge and rinse twice with clean water. A wet-dry vacuum may be used.

6) Polish surface dry with clean, dry towels or buff with soft lambs wool pad.

7) Rinse with clean water and buff dry with clean towels


Aqua Mix Poultice Stain Removal Guide

Aqua Mix Poultice Stain Remover Technical Data Sheet

Aqua Mix Poultice Stain Remover Safety Data Sheet


Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Stone Care Products > Stain Removers > Aqua Mix
Aqua Mix > Problem Solvers
Aqua Mix
Stone Care Products
Stone Care Products > Stain Removers
Aqua Mix > Problem Solvers > Poultice Stain Remover