Submit search
Sale!
Schluter-DITRA is a polyethylene membrane with a grid structure of square cavities, each cut back in a dovetail configuration, and an anchoring fleece laminated to its underside.
Schluter-DITRA-DRAIN is a drainage membrane designed for use within thin-bed ceramic and stone tile assemblies in exterior applications. DITRA-DRAIN is typically installed over the Schluter-KERDI bonded waterproofing membrane.
Schluter®-KERDI is a pliable, sheet-applied, bonded waterproof membrane and vapor retarder with limited crack-bridging capabilities. Now with printed grid lines.
Schluter-KERDI-DRAIN is a floor drain specifically designed to allow connections to Schluter®-KERDI or other load-bearing, bonded waterproof membranes.
The Schluter Kerdi Drain adapter kit is utilized to adapt, rather than remove, traditional clamping ring drains to bonded waterproofing applications.
Schluter-KERDI-BOARD-SN is a prefabricated shower niche made of KERDI-BOARD that can be installed in both Schluter®-KERDI and KERDI-BOARD wall assemblies
The KERDI-SHOWER-SB shower bench is available in triangular and rectangular configurations.
New for March 2019! The new Schluter Shower Kits now feature shower trays with the Kerdi Waterproofing Membrane already adhered to the tray for an even faster and easier shower installation!
New for March 2019! The SCHLUTER-KERDI-SHOWER-LT is a prefabricated expanded polystyrene sloped trays with integrated KERDI waterproofing specifically designed to accept the KERDI-LINE linear drain.
New for March 2019! The Schluter Kerdi-Shower-T trays are made of lightweight, expanded polystyrene (PS40) for constructing mortar-free shower bases and feature center drain outlet designed to integrate with the Schluter-Kerdi-Drain.
New for March 2019! Schluter Kerdi-Board-SC is a prefabricated shower curb, made of KERDI-BOARD, for use in conjunction with the Schluter-Shower System.
Use KERDI-BAND, in widths of 5" (12.5 cm), 7-1/4" (18.5 cm), or 10" (25 cm) to seal butt joints or corner joints.
Schluter-DITRA-XL serves as an uncoupling layer, waterproofing membrane, and vapor management layer that accommodates moisture from beneath the tile covering.
KERDI-FLEX, in 5" (12.5 cm) or 10" (25 cm) widths, is used to seal expansion joints or flexible edge joints.
Schluter-KERDI-KERECK are preformed, seamless corners made of Schluter-KERDI for waterproofing inside and outside corners.
Schluter®-KERDI-FIX is a single component, waterproof sealing and bonding compound with a silane-modified polymer base.
Schluter Square Notch Trowel 1/8" x 1/8" for Kerdi installation.
The DITRA-TROWEL is specifically designed to install Schluter-DITRA.
DITRA-HEAT is the only system that provides floor warming and uncoupling in a single layer. The heating cables are easily snapped into place on top of the uncoupling mat with no clips or fasteners.
Schluter Kerdi-Seal Mixing Valve 4-1/2" Opening
The KERDI-SHOWER-LS is a polystyrene sloped tray with integrated Schluter-KERDI waterproofing.
Schluter®-KERDI-SEAL-PS eliminates the use of sealant at specified protrusions for clean and simple application.
Schluter-Ditra-Roller is used to embed Ditra/Ditra-XL in the bond coat during membrane installation.
The DHERT102/BW is a programmable digital touchscreen thermostat designed to control the Ditra-Heat heating cables.
Schluter-DITRA-HEAT-TB is the newest electric floor warming system with integrated thermal break from Schluter.
Schluter-KERDI-BOARD-ZT are galvanized steel washers used to fasten KERDI-BOARD to metal or wood stud framing.
Schluter Dilex-AHK End Caps are for use with the Dilex-AHK cove-shaped profiles.
Back to top